两个旋钮和一条带:沿它走,穿过它,然后倾转电子束,弱束就属于你了。
一个模拟的双倾样品台,前方是模拟荧光屏,显示整个菊池图,尽在掌握。将任意晶带轴交点拖到中心,选一条穿过它的菊池带,然后驱动 alpha 和 beta:沿带偏离晶带轴,设置双束,倾转电子束获得中心暗场,看看为什么 3g 突然满足布拉格条件。右侧的位错像随操作逐渐变窄。
双束与弱束模拟基于 Howie–Whelan 两束动力学理论,适用前提是:只有一束强衍射被激发、样品为平行薄片、吸收用等效吸收处理。以下情况结论会失真:
g·b = 0 时位错并非绝对不可见:刃型分量仍有 g·(b×u) 残余衬度。工具用琥珀色标出的正是"靠不住"的那几格。取一个候选柏氏矢量 b = a/2[110] 和反射 g = (111),用点阵矢量做点乘:
g·b = (h·bx + k·by + l·bz) × a/2
结果为 0 即判不可见,为整数即判可见,为 1/3、1/6 等分数则对应不全位错的弱像。用纸笔算两格,再和表格里的绿色/灰色格子对照,能立刻发现是否把"残余衬度"当成了"不可见"。
当 α = β = 0 时,[011] 晶带轴位于光轴上(在 晶体与行 下另选一个)。α 使花样在屏幕上上下移动,β 左右移动;β 轴骑在倒易杆上,因此当倒易杆大幅倾斜时,其杠杆作用按 cos α 缩小。
| 反射 | s (nm-1) | w = sξg | 布拉格检查 |
|---|
Go 按钮将样品台动画移动到该步骤的目标位置(就像你用倾斜旋钮操作一样,只是更快)。超出样品台极限的目标会被标记;重新安装或使用相反的 g。
最终图像只与你设置的激发误差一样窄。你通过按固定顺序倾斜晶体(样品台)和光束(暗场偏转器)来设置它。
当光束或晶体倾斜时,斑点会移动。菊池线固定在晶体上,只有当晶体倾斜时才移动。这一差异就是全部诀窍。
靠近透射束的线是暗的,较远的线是亮的。只有当光束位于该平面内时,这对线才对称,沿整个带内任意位置皆如此。
对准一个晶带轴。沿带离开它。设置双束条件。倾斜光束以获得中心暗场。将光阑套在 g 周围并拍摄图像。
弱束暗场是一种倾斜配方。最终图像只与你在过程中设置的激发误差一样窄,而激发误差是通过按固定顺序倾斜晶体(用样品台)和光束(用暗场偏转器)来设置的。
屏幕显示两类东西:斑点,当光束倾斜和晶体倾斜时都会移动;以及菊池线,它们固定在晶体上,只有当晶体倾斜时才移动。这一差异就是全部诀窍,因此模拟器同时绘制两者,以真实花样显示的方式展示缺(暗)侧和过(亮)侧:靠近透射束的线是暗的,较远的线是亮的,只有当光束位于该平面内时,这对线才对称,沿整个带内任意位置皆如此,包括晶带轴。
The rod tilt α moves the whole pattern up and down the screen. The cradle tilt β moves it left and right.
The β axis is carried by the rod, so its leverage falls as cos α. The orientations you can reach form a curved patch, not a rectangle.
A band rarely runs along either axis, so walking along it and across it takes a mix of α and β. Dragging the pattern solves the mix for you; the knobs and arrow keys move one axis at a time.
The rod tilt α moves the whole pattern up and down the screen; the cradle tilt β moves it left and right, about an axis that is carried by the rod, so its leverage falls as cos α at large rod tilts and the set of orientations you can reach is a curved patch on the sphere rather than a rectangle.
A Kikuchi band rarely runs exactly along either axis, so walking along a band and then across it takes a combination of the two, and the combination changes as you go. Dragging the pattern with the mouse solves that combination for you and shows the α and β it implies; the knobs and arrow keys let you do it one axis at a time, which is what the microscope makes you do. The compass in the corner of the screen shows which way each knob moves the pattern from where you are now.
从倒易点阵点到 Ewald 球的距离,点在球内时为正。一个倾斜角就决定了整个系统行中所有斑点的 s。
The effective extinction distance is ξg/√(1 + w2)。线宽随其变化,这就是大 s 会使线变窄的原因。
Computed from the structure factor with Peng’s 1996 scattering factors. Al 111 at 100 kV comes out at 55.6 nm, the classic table value.
激发误差 s 是从倒易点阵点到 Ewald 球的距离,当该点位于球内时为正。对于系统行,sng = −n gz − n2λg2/2, where gz is the component of g along the incident beam; the whole row is set by one tilt angle.
The dimensionless w = sξg is what the image cares about: the effective extinction distance is ξg/√(1 + w2),暗场中的背景强度大致按 1/(1 + w2), and the dislocation line width scales with that effective distance, which is why a large s narrows the line. 消光距离 are computed from the structure factor with Peng's 1996 scattering factors and the relativistic mass correction: Al 111 at 100 kV comes out at 55.6 nm, the classic table value; copper values run 10 to 20 percent above the 1965 table, which used older scattering factors.
针对螺型位错的双束 Howie-Whelan 计算,柱近似,各向同性弹性,轻微吸收。系统行中的其他束未包含在内。
几何关系是精确的,明暗不对称性遵循光束与平面的夹角。没有带轮廓,没有漫散射模型,也没有 HOLZ 线。
一种显示模型:它放置各光束并显示哪些被激发,而不是多光束计算会使它们有多亮。
无回程差、无漂移、无图像位移。未对相机旋转建模,因此请用已知倾转角校准一次。
该图像是在柱近似下对螺型位错进行的双束 Howie-Whelan 计算,采用各向同性弹性,并带有轻微吸收(ξ'0 = ξ'g = 10ξg);它仅使用成像反射的 s,因此未包含其他行束的微弱影响(系统行动力学效应,在实际中对 g(3g) 有影响)。菊池线强度是示意性的:几何是精确的,暗-亮不对称性遵循束-面夹角,但没有漫散射模型、没有带轮廓、也没有 HOLZ 线。
斑点来自与菊池图导航器相同的拼接图:视野中的每个晶带轴贡献其零阶网,延伸到其最近斑点的数倍距离,每个反射绘制在其实际衍射的位置,大小由 |F|2 决定,并按其激发误差以双束包络衰减,但在晶带轴约一度半范围内除外,那里整个网按多束散射点亮的方式被照亮(关闭衰减以查看裸网)。
这是一个显示模型:它放置束并显示哪些被激发,而不是多束计算会使它们多亮。样品台是理想的双倾台,无回程差且无样品漂移;束倾转是理想偏转,无图像位移。未对相机旋转和翻转建模:在您的显微镜上,图案可能相对于样品台轴旋转,您应使用已知倾转角校准一次。
已核对(2026 年 10 月)。 与 Cockayne、Ray 和 Whelan 1969 年相比:当 3g 处于布拉格条件时,模拟器的 g 激发误差为 sg = λ|g|²,对于 100 kV 下的 Cu 220 给出 0.227 nm-1 (他们的情况,约 2 × 10-2 Å-1), 0.154 nm-1 在 200 kV 下,以及 200 kV 下 g(5g) 的 0.307 nm-1 。100 kV 下 Cu 220 的布拉格角为 14.48 mrad(λ/2d)。它计算的 100 kV 下 Cu 220 的消光距离 43.9 nm 与本网站的 SAED 图案模拟器一致,完美晶体双束强度在 s = 0 和 t = ξ 时为 1.000g/2.
@misc{tripathy2026weakbeamtiltsimulator,
author = {Tripathy, Manisha},
title = {弱束倾转模拟器},
year = {2026},
howpublished = {\url{https://untetheredatom.com/tem/weak-beam-tilt-simulator}},
note = {Interactive web tool}
}